Product Overview
The NUMOBAMS precision mini bench drill is a 710 W bench drill press with a 1.5–13 mm keyed chuck, built for people who need accurate vertical holes in small parts rather than heavy material removal. It stands on a slotted metal base, carries its head on a machined column, and feeds on a lever with a ball end, so the bit travels straight down under control instead of being pushed by hand. The drill is built for us by Chinese milling machine manufacturers we have worked with since 2016, and every unit is checked and prepared before it leaves the warehouse.
It is a drill, not a mini milling machine. The head feeds straight down and the table does the holding: there is no sliding table to crank in two axes, no drawbar and no side load on the column. That is the point of it. Everything about the machine is arranged around making one hole at a time land exactly where you marked it, which is what jewellery benches, PCB benches and model workshops actually need.
Set-up is a bench-top job. The base is slotted so it can be bolted to a worktop, the column wipes down in seconds, and the whole machine can stay in place between jobs instead of being packed away. If you have been drilling with a hand tool and a clamp, this is the step that takes the wobble out.
Key Features
- 710 W motor with a stepless 800–3000 r/min range — slow it down for a 13 mm hole in aluminium or brass, open it up for small bits in plastic, PCB or wood. The dial covers both without a belt change.
- Column-and-base layout, not a hand-drill bracket — the head rides a machined vertical column, the same arrangement you find on a mini milling machine, so the bit stays square to the work as it enters.
- 60 mm spindle stroke on a lever feed — the ball-end handle gives you a controlled, even feed through the whole stroke, so you feel the cut rather than forcing it.
- Depth stop rod and pointer scale — set a depth once, lock it, and repeat blind holes across a batch without measuring each one.
- Keyed 1.5–13 mm chuck — a standard keyed chuck, tightened with the supplied chuck key, holding straight-shank bits from 1.5 mm up to 13 mm.
- Slotted work base — the slots take the optional cross vise or let you clamp a part straight to the table.
- Honest about its limits — the head only feeds vertically. Facing a plate or cutting a slot is a metal milling machine's job, and no amount of careful setup turns this drill into one.
Specifications
| Specification | Value |
|---|
| Model | BG-5156E |
| Rated voltage / frequency | 220–230 V, 50 Hz |
| Motor power | 710 W |
| No-load speed | 800–3000 r/min |
| Chuck capacity | 1.5–13 mm |
| Maximum drilling capacity | 13 mm |
| Spindle travel | 60 mm |
| Workbench surface | 170 × 185 mm |
| Maximum chuck-to-worktable distance | 190 mm |
| Working radius | 112 mm |
| Feed | Lever with ball-end handle |
| Work base | Slotted metal base |
Workbench Capacity & Reach
Vise & Configuration Options
Setup & First Run
- Stand the drill on a solid bench and bolt the base down through its slots. A bench that flexes shows up as chatter on thin sheet, so choose the sturdiest surface you have and fasten it.
- Wipe the protective oil off the column, table and chuck, then run the head through its full travel by hand to confirm it moves freely before anything is switched on.
- Fit the feed handle and set the depth reference: bring the chuck down to the table, zero the pointer, and you have a starting point for every depth after that.
- Open the chuck, seat the bit fully, and tighten with the chuck key in two or three key positions rather than one, so the bit centres more evenly.
- Set the speed on the dial before switching on. Large bits and hard material want the low end; small bits in plastic, PCB or wood want the high end.
- Drill a test hole in scrap of the same material and thickness, check the depth against the pointer, and adjust the stop before you touch the real part.
Maintenance & Care
- Wipe down after every session — chips left on the table and in the chuck jaws are the usual reason a bit stops running true. A brush and a dry cloth take less than a minute.
- Oil the column, keep the table dry — a light film on the column and quill keeps the head sliding smoothly; leave the table dry so clamps and vises grip.
- Look after the chuck jaws — brush them out before tightening, and tighten in more than one key position so the bit seats centred.
- Respect the feed — because the head only feeds straight down, the column carries nothing like the side load of a metal milling machine, but forcing the lever is still the quickest way to break a small bit.
- Choose speed before pressure — a bit running too slowly for its size will squeal and heat up. Drop the feed and raise the speed rather than leaning on the handle.
- Store it dry and covered — a cloth over the head keeps dust out of the chuck and stops condensation forming on the column in an unheated workshop.
Matching Machines in the Range
If you also need to cut sideways
A bench drill only feeds vertically. For facing a plate, cutting a slot or squaring an edge you want a milling machine, and our range covers that with the Super VM25L Plus and VM25L (1100 W brushless, with an auto feeder and foot switch on the Plus) and the smaller VM18L Plus and VM18L (750 W brushless). Those machines share the same bench logic — compact, vertical, one operator — but they carry a sliding table and a spindle built to take side load.
If your work is round rather than flat
Turning is a different machine again. Our lathe range runs from the compact NU180E up to the long-bed WL800, and the drill stays useful alongside any of them for cross-holes, dowel pins and fixture plates.
What carries over
Bits, vises, clamps and a bench light are shared across all of it, so adding a mill or a lathe later does not mean starting the tool kit again. If you are unsure which machine a job actually needs, describe the part and the operation and we will tell you which one belongs on the bench.
Ordering & Delivery
- Dispatch — we ship within 90 days of order confirmation.
- Delivery — orders move on our tax-free, door-to-door delivery service. Established routes serve cities including Tokyo, Melbourne, Madrid, Warsaw and Los Angeles; send us your delivery address and we will confirm the route and timing that applies to it.
- Payment — credit card or T/T bank transfer.
- Documentation — a printed handling manual travels in the carton. If you want the exploded parts view or a spare-parts list before you order, ask our team.
- Choosing a configuration — tell us the material, the hole sizes and whether any holes are angled, and we will confirm which of the four configurations fits the work.
- Who you are buying from — NUMOBAMS has supplied compact machine tools built by Chinese milling machine manufacturers since 2016, and the team that prepares your drill is the same team that answers questions about it afterwards.
- Ordering more than one machine — as milling machine suppliers we ship drills alongside mills, lathes and accessories; send the list and we will check the combination and the delivery before you commit.
Supply Chain & Delivery Assurance
NUMOBAMS is a China-based machinery trading company working from Changsha, Hunan, with a selected network of manufacturing partners built up since 2016. That position lets us consolidate a full workshop order — machines, tooling and spare parts — into one shipment, inspect and prepare each unit before dispatch, and keep spare parts available long after delivery. We ship to Europe, the US and Canada on a tax-free, door-to-door basis, and usually dispatch within 90 days of order confirmation.
FAQ
Q1. What materials can the mini bench drill work in?
Wood, plastic, light metals such as aluminium, brass and copper, and circuit board material. Jewellery blanks, model parts, brackets and PCB sampling all sit comfortably inside that list. It is a 710 W bench drill rather than a production machine: hardened steel, thick plate and heavy stock belong on a larger drill or a mill, and the 1.5–13 mm chuck sets the practical limit on bit size.
Q2. What is the difference between this bench drill and a mini milling machine?
A drill feeds straight down; a mill also moves the work sideways under a cutter. This machine has a vertical column, a lever feed and no sliding table, so it produces accurate vertical holes and nothing else. If your job needs slots, faces, shoulders or square edges, you want the mill — the table movement is the whole point of it. Many benches run both: the drill stays set up for holes while the mill handles the cutting.
Q3. Can I use it on a 110 V supply?
The machine is rated 220–230 V, 50 Hz, as marked on its data plate. On a 110 V workshop supply it needs a suitable step-up transformer rated for a 710 W motor, and that is worth confirming with us before you order rather than after the crate arrives. Tell us what your workshop supplies and we will say what is required.
Q4. Do you offer custom builds, different colours or other voltages?
We supply this drill as a standard machine in four configurations: on its own, with the mini multi-function cross vise, with the 3-inch swivel-base tilting vise, or with both. That covers most benches. If your work needs something outside the standard build, tell us the material, the hole sizes and the operation, and our technical team will confirm what is possible before you commit to an order.
Q5. The drill is running hot or sounding rough — what should I check?
Switch off first. Most of the time it is a chip caught in the chuck jaws, a bit that is too large for the speed you set, or feed pressure that is too heavy for the material. Clear the chuck, check the bit is seated in more than one key position, and drill with a lighter feed at a higher speed. If the noise continues with an empty chuck and no load, send us a short video and we will work through it with you.
Q6. What comes in the carton with the drill?
The machine itself, the chuck key, a set of hex keys, fastening screws for the base and a printed handling manual. Bits are chosen to suit your work, so pick them from the 1.5–13 mm straight-shank range the chuck accepts — tell us the sizes you use most and we will check them against the machine's speed range.